How To Use Countersink In A Sentence
-
You can even countersink and cover the screws with a dab of caulk.
-
Countersink nail and screw heads that are sticking up above the surface.
-
Fasten the bottom of each brace with a 6-inch machine bolt and countersink the washer and nut.
-
Depending on how far the bolts stick out beyond the boards, we either countersink the nuts or wrap two layers of duct tape over the ends of the bolts to prevent damage to the greenhouse film.
-
Place the hinge leaf in the mortise and position the self-centering tool in the countersink recesses of the hinge.
-
Construction began by countersinking the holes for the bolster rivets slightly.
-
Fabricators can use one holder with a variety of special forming inserts - anything from countersinks and continuous beads to formed embosses for logos and branding.
Manufacturingtalk - manufacturing industry news
-
Use a nail punch to countersink all nail heads approximately 1/8 ‘below the wood surface.’
-
You can add a paint mixer, right-angle drive, wire brushes, wood countersinks, and even saws, lathes, and rotary rasps and files.
-
It's helpful to first pre-drill a small hole in the wood where you want to countersink the brass screws.
-
Search out any protruding nail heads and countersink them with a nailset.
-
Fasten the bottom of each brace with a 6-inch machine bolt and countersink the washer and nut.
-
To help prevent recurrence, countersink the nails and swab the holes with a water repellent.
-
To drive(a screw or bolt) into a countersink.
-
Use a hammer and nail set or an electric drill with countersink bit to join the frame pieces.
-
Use 12 or 16 HDG finishing nails and countersink them with a nail set.
-
After the first sanding, check to see if any nails are now protruding, and, if so, countersink them.
-
Drill and countersink screw holes for mounting screws.
-
First, countersink the nails and swab the holes with a water repellent.
-
Countersink the bolt holes to accommodate washers and nuts.
-
For special applications-such as reaming and countersinking-the speed is adjusted electronically.
The Earth Times Online Newspaper
-
Drills are to be procured from the various dealers, but can be made from steel wire softened in the fire and filed to a sharp three-cornered point -- afterwards tempered to hardness -- for the smaller eggs, or filed up for the larger eggs to the pattern of a "countersink" used for wood; indeed, the smallest-sized
Practical Taxidermy A manual of instruction to the amateur in collecting, preserving, and setting up natural history specimens of all kinds. To which is added a chapter upon the pictorial arrangement of museums. With additional instructions in modelling a
-
Working from below, drill several clearance/pilot/countersink holes through the subfloor and into the flooring.
-
Drill four 3/16-inch clearance holes in each rib before countersinking the top surface to bring the screw head flush.
-
There are those operations that are strictly drilling operations, but we also use drilling machines to perform other operations such as reaming, tapping, countersinking and counterboring.
-
I drilled larger holes to hide the screw heads; this is called countersinking the screws.
Mother Earth News Latest 10 Articles
-
When applying directly over an old floor, countersink any protruding nails and sand off any paint, wax, or varnish that might affect the adhering ability of the adhesive.
-
Alternatively, they can be retrofitted to devices such as countersink gauges, measuring situations where conventional 1: 1-ratio indicators would be rendered useless.
Manufacturingtalk - manufacturing industry news
-
/16 inches and includes a two-speed gearbox for efficient drilling on site-the two mechanical speed levels enable an expanded range of application and uses, such as reaming and countersinking.
The Earth Times Online Newspaper
-
What type of countersink will you use to deburr a bore hole?
6. The Technological Steps of Making Pinned Joints
-
Search out any protruding nail heads and countersink them with a nailset.
-
Place the hinge leaf in the mortise and position the self-centering tool in the countersink recesses of the hinge.
-
To drive(a screw or bolt) into a countersink.
-
The process can accommodate features such as countersinks, extrusions, semi-pierces, weld projections, coined chamfers, counter bores, and offsets.
