How To Use Cylinder head In A Sentence
-
Weight concerns mandated that the cylinder heads and crankcase are both made of cast aluminum.
-
The engine also has a sportbike-derived chain-and-gear camshaft drive system that allows for a short/narrow cylinder head design and reduced overall engine height.
Quad 2009 ATV Buyers Guide
-
Irreparable damage had been caused to the A7 rocker gear, cylinder head, cylinder liner, piston, connecting rod, big end bearing and the trombone.
-
Allan, a mechanic, was removing a cylinder head from a Harley-Davidson motorbike, when he spotted a world-famous heart surgeon in his garage.
-
It turns out that Keller knowingly allowed some cracked cylinder heads to ship and twenty-one P-40s they were installed in crashed because of it.
Lance Mannion:
-
The foundry is charging its furnaces to cast the engine block and cylinder heads.
Times, Sunday Times
-
Catalytic converters are being mounted closer to the engines to improve their performance and exhaust manifolds are being integrated into cylinder heads.
-
A ground strap bolted to the engine block may not do the job; head gaskets, silicon, and bolt sealer can electrically insulate the cylinder heads from ground.
-
The term "flathead" arises from the flat appearance of the main cylinder head block.
Undefined
-
Unlike two-stroke engines that have simple openings or ports for intake and exhaust, four-stroke engines have intake and exhaust valves at each cylinder head.
-
The only effective remedy is to install hardened valve seats or a replacement cylinder head, both expensive options.
-
Leonard designed the block, which has giant bore spacings and mammoth cylinder heads.
-
A new cylinder head design employs the transfer arm and pushrod to locate the exhaust valve across the head from the dual intake valves.
-
Massimo Bordi, developed a high-performance, ultra-efficient four-valve desmodromic cylinder head, the Desmoquattro, that propelled Ducati motorcycles to the lead in international races.
NYT > Home Page
-
Now there's a thousand ways you can cheat, especially in the motor area, carburation, cylinder heads, manifolds.
Oral History Interview with Junior Johnson, June 4, 1988. Interview C-0053. Southern Oral History Program Collection (#4007)
-
Very small roller cam followers are installed in the cylinder head to operate the valves instead of the conventional bucket-type tappets, and here friction is cut by about 70 per cent.
-
The machined engine blocks, cylinder heads and clutch and transmission cases meet with the other engine components for the final assembly process.
-
The engine block and cylinder head are made of cast aluminium.
-
The combustion chamber of a four-stroke engine is designed to induce turbulence through the addition of ‘squish’ areas in which the top of the piston is the mirror image of a corresponding area of the cylinder head.
-
Converters mount directly to the exhaust port of each cylinder head.
-
You get one cylinder head rather than two, two cams rather than four, one cam drive system rather than two and so on.
-
At Castiglioni's behest, Ducati's chief engineer, Massimo Bordi, developed a high-performance, ultra-efficient four-valve desmodromic cylinder head, the Desmoquattro, that propelled Ducati motorcycles to the lead in international races.
The Globe and Mail - Home RSS feed
-
Precisely how an engine is sealed will depend on its layout, but typically we will link the cam covers to the cylinder heads, and the sump to the block.
-
Decarbonize the cylinder head with a good top engine cleaner to get rid of the deposits.
-
The engine block and alloy cylinder head is shared with the 1.4-litre Energy engine so the bore is identical.
-
The bolts are torqued in a special sequence to draw the intake manifold and its molded rubber gasket on to the cylinder head.
-
The engine block and alloy cylinder head is shared with the 1.4-litre Energy engine so the bore is identical.
-
Attached to the crankshaft is a set of titanium connecting rods and forged aluminum pistons, which, when combined with the cylinder heads, delivers a 9.1: 1 compression ratio.
Top Speed
-
To fully inspect for damage, all components above the cylinder block were removed except for six of the 16 cylinder heads, one of the two charge air coolers and the engine controls.
-
The fuel injectors are found where the intake air runners connect to the cylinder heads.
-
The basic casting method - design principle of cylinder head was introduced.
-
My dealer tells me the plugs are seized in and that it would cost 1,000 to take off the cylinder heads to remove them.
Times, Sunday Times
-
It is perfectly possible to replace the hot spots in a Land Rover cylinder head.
-
Ken peered over his oxygen mask at the tachometer and cylinder head temperature gauges for number three.
-
The engine block and alloy cylinder head is shared with the 1.4-litre Energy engine so the bore is identical.
-
Continually running an older car not designed to use unleaded petrol will eventually cause the coating to wear away, causing damage to the valves and cylinder heads.
-
The two-stroke cylinder head of the 100 cc TVS bike that was converted has been replaced by a new cylinder head, which suits only four-stroke engines.
-
We're also trying to improve some existing products - like superchargers and cylinder heads - that might eventually give us an edge.
-
The engine-component and cylinder-head moratorium includes, but is not limited to, engine blocks, cylinder heads, intake manifolds, fuel injectors, and superchargers.
-
Fix Auto Body of Ontario did the bodywork and paint and Precision Cylinder Heads modified the heads.
-
The cylinder head is a single overhead camshaft, two valve type.
-
If a $4 cylinder head gasket blows, it costs the customer $1,000 in engine repairs.
-
Generally, the cylinder and the cylinder head bolt together with a thin gasket pressed between them to ensure a good seal.
-
Both models feature the high-performance cylinder head from the sport TRX250X for increased performance from its lightweight, oil-cooled 229cc engine.
Quad 2009 ATV Buyers Guide
-
Exhaust port, piston, and cylinder head are decoked.
-
The question is the charge of gas, exploded in the cylinder head, which is the motive force of every piston-stroke.
-
The unpressurized oil drain ducts from the cylinder heads are arranged on the outer sides, as in the case of V engines.
-
A single big cam is used to pushrod operate two valves per cylinder at the top end, inside aluminium cylinder heads.
